EasyPLC Drivers

EasyPLC Drivers




With the EasyPLC Registered version some Drivers are provided free. There are others that must be acquired separately, also if you need any particular driver, it can be performed under special request, ask for prices and delivery.

Serial DriverThis drivers provides 8 inputs and 8 outputs, sending/receiving only one byte in binary modeFree with EasyPLC registered version
Joystick DriverThis drivers allows to use a Joystick to read two axis (X and Y) like two analogic inputs and the buttons like digital inputsFree with EasyPLC registered version
Parallel Port DriverUses the PC parallel port to manage the digital I/O provided by this port.
In total are: 5 inputs and 8 outputs
Free with EasyPLC registered version
Machines Simulator DriverThis driver must be used to communicate with Machines Simulator softwareFree with EasyPLC registered version
PhidgetsInterfaceKitDriver to communicate with Phidgtes PhidgetsInterfaceKit I/O cards via USB portFree with EasyPLC registered version
PhidgetsWebServiceDriver to communicate with Phidgtes PhidgetsInterfaceKit I/O cards via WebServiceFree with EasyPLC registered version
Siemens Simatic Step 7 – PLCSIMDriver to directly communicate with Siemens Simatic Step 7 software.
More Info
Free with EasyPLC registered version
Siemens PLCWith Siemens PLC driver for EasyPLC you will be able to connect your PC where is running EasyPLC software with a physical (or simulated) Siemens PLC via Ethernet protocol.
S7 300 / S7 400 / WinAC / S7 1200 / S7 1500 PLCs
Free with EasyPLC registered version
TwinCAT v3Use this driver for communication with TwinCAT v3 software.

More Info

Free with EasyPLC registered version
CODESYSUsing the Generic OPC Driver you will be able to connect with Codesys system. See video https://youtu.be/us1p9VCtvtY

Download the configuration instructions here CODESYS OPC Driver for EasyPLC

TCP/IPDriver to communicate two PCs with EasyPLC via TCP/IP protocol, it can also be used like a HTML server, then with PC or movil device EasyPLC can be accessed remotely.
Using a Phone to manage remote I/O
Free with EasyPLC registered version
Nirtec_USB_1516 CardDriver to communicate with Nirtec_USB_1516 cardFree with EasyPLC registered version
ModBusWith this driver is possible to communicate with external devices using the ModBus protocol. This driver accepts the Modbus serial RS-232 (RTU) and TCP/IP protocols.Free with EasyPLC registered version
Generic OPC DriverUsing this driver will be possible to communicate with Real or Simulated PLC’s using the standar OPC protocol specifications.Free with EasyPLC registered version
OPC Driver EnhacedOPC driver enhaced to communicate with: Rockwell RSLogix OPC Server, OPC.SimaticNET and Mitsubishi MX OPC 6
Arduino UNOYou can use an Arduino UNO card and manage it with EasyPLC. Arduino UNO provides 12 configurable digital I/O (6 of then can be programmed as analogic output) and 6 analogic inputs.
With Arduino UNO driver for EasyPLC you can configure each pin as I/O (digital or analogic) and can read/write the signals in the EasyPLC logic programs.
Important: the Firmata (StandardFirmata sketch) must to be loaded on Arduino UNO in order to use his driver (included in Arduino UNO IDE or download from: http://www.firmata.org)
Free with EasyPLC registered version
Virtual PanelUse a virtual panel with lights, push buttons and selectors to write and see the logic state of the I/OFree with EasyPLC registered version
IOIO OTGAllows to manage a IOIO OTG card. Provides 46 digital I/O (3,3V)Free with EasyPLC registered version
PoKeys57UThis drivers allows to manage a Pokeys57 interface USB card. Provides 55 digital I/O (5V tolerant), 7 analog inputs (12-bit). All the I/O are controlled by EasyPLC. PoKeys57 can be used as industrial or electronic interface with others systems or data acquisition boardFree with EasyPLC registered version
Yottacontrol driverDrivers for Yottacontrol A-1055S and A-1860 cards
Shared memory I/O driverUse the API Windows FileMapping functions in order to create your own I/O driver with your favorite programming language using these functions. The driver allows to manage 256 digital inputs and 256 digital outputs. The first 32 bytes must contain the digital input values, the next 32 bytes will have the digital outputs values.
Simulation DriverDriver for Simulation purposes.
Use this driver for test your logic programs, using a windows where you can press for simulate inputs and see the outputs values
USB OPTO RLY88Driver to manage the USB OPTO RLY88 card.
Remote PanelUse an Android based Tablet or smartphone to communicate with EasyPLC & Virtual PLC and manage remotely the I/O with a Virtual Panel Interface.


Download the free Android RemotePanel2

Free with EasyPLC registered version